Todays Jobs
Job Role
Job Types
Sector
Aircraft type
Senior Digital Design Engineer I
Apply now
Location: Virginia
Job type: Permanent
Aircraft type:
Contact:
Sector: Manufacturing
Job Role:
-
Requisition ID
106849
USA-Virginia-Ashburn
Description
Senior Digital Design Engineer I
We are a company of innovators, game changers, and entrepreneurs. As a prime contractor, we provide a broad range of communication, electronic and sensor systems used on military and commercial platforms across the globe. We embrace innovative and progressive ideas to advance our products for military and commercial customers. Electronic Systems Segment (ESS) provides a broad range of aerospace systems, security and detection systems, and pilot training. We are searching for a Senior Digital Design Engineer I in our Advanced Systems & Technologies (AS&T) division, located in Ashburn, VA.
L3 AS&T is built on the proposition that a small team of the right people can do what others will not even attempt. We specialize in developing disruptive, next-generation technologies for advanced small Unmanned Air Systems (UAS / UAV), advanced radar systems, next-generation weapon systems, and other RF sensor technologies using small company agility and big company experience. We’ve earned a reputation for providing vital warfighter solutions at a faster pace than traditional DoD contractors, so if you like the idea of hands-on experience designing, building, testing and fielding new technology at a fast pace and supporting the vital missions of our warfighters, then L3 AS&T may be the company for you.
As our Senior Digital Design Engineer I , you will be an integral part of our Unmanned Air Systems team. You will hold responsibility for design, test, and integration of complex digital circuit card assemblies that target advanced tactical weapon platforms and sensors. Contributions are made as you work in a small team environment, allowing more touch points in the design process.
You will demonstrate success by:
*
Participating in electrical design tasks including requirements analysis, specification generation, interface definition, component selection, circuit simulation, schematic capture, and board layout.
*
Contributing to advanced digital CCA design synthesis using both high performance and conventional converters, data interfaces, memory, processor and logic devices.
*
Participating in layout activities for high layer count, high speed signaling, and complex via structure (including blind, buried and micro vias) for PCBs
*
Designing product support test hardware including breakout boards and interface cable fixtures
*
Interfacing with software and FPGA engineers to test and troubleshoot electrical circuits and interfaces of the CCAs
*
Identifying high risk circuits functions to simulate and prototype/breadboard before creation of full design
*
Developing test plans and procedures for digital subsystems and all relevant documentation for design description and requirements
Our Values are an integral part of who we are. We seek candidates who share our values:
* Integrity
* Excellence
* Accountability
* Respect
Qualifications
Required experience and skills
:
*
Must be a U.S. citizen with the ability to obtain a DoD clearance; must also be able to obtain and maintain additional clearances as required
*
5-7 years of broadly based design, simulation and test experience with digital circuits and systems
*
3 years of lab integration and troubleshooting electrical subsystems
*
Experience with schematic capture tools to generate a complete schematic, with exposure to Altium preferred
*
Understanding of appropriate board materials and general board layout techniques
* Design for Test, Design for Manufacturing, and/or Design to Cost experience
*
Proficiency with circuit card and wiring harness fabrication techniques. Experience with hybrid/flex circuit card designs is strongly desired.
*
Electrical system diagnostic skills, including the ability to operate diagnostic equipment such as oscilloscopes, spectrum analyzers, bus analyzers, signal generator, and power meters
*
Physical requirements include the ability to travel up to 10% and the ability to lift up to 50 lbs.
Desired
:
* Use of HyperLynx or other board simulation tools
* Experience with Mentor schematic capture and layout products
* Product design experience with repetitive production applications
* Board layout experience
* Working knowledge of LabView, MatLab, Python
*
A working knowledge of RF communication techniques and devices is strongly desired
SAVING LIVES AND MAKING THE WORLD A SAFER PLACE TO LIVE
L3 Technologies, Inc. is proud to be an Affirmative Action/Equal Opportunity Employer. L3 provides equal employment opportunity for all persons, in all facets of employment. L3 maintains a drug-free workplace and performs pre-employment substance abuse testing and background checks. We encourage all qualified applicants to apply for any open position for which they feel they are qualified and all will receive consideration for employment without regard to race, color, religion, age, gender, sexual orientation, gender identity, national origin, citizenship status, marital status, genetic information, disability, protected veteran status or any other legally protected characteristic.
IND2
US Security Clearance Required
:
Secret
Schedule
:
Full-time
Shift
:
Day - 1st
Travel
:
Yes, 10 % of the Time
Organization
:
AS&T - Radar & Weapon Systems-21001080
Job Level
:
Individual Contributor
Job Posting
:
Jun 4, 2019, 9:00:26 PM
Job
:
Engineering Design, Drafting
Email this job
To access this job from another device, Email this information to yourself.
Your name
Name should not be empty
Recipient’s email address
Error
Email should not be empty
Error
Please enter a valid Email
SUBMIT
Success!
Email has been sent sucessfully
No locations found
Apply for this job